RF-Max Digimax 210 Uživatelský manuál stáhnout pdf (Strana 5)

Keene Electronics Catalogue 2005Tel 0870 990 9000 Fax 01332 830551 Web www.keene.co.uk

Tel 0870 990 9000 Fax 01332 830551 Web www.keene.co.uk

109

Remote controls Home automation Video tapes & accessories

Wireless wall switch

A wireless switch that can be stuck or

screwed to the wall and gives you control of

two X10 addresses. Ideal for controlling

appliance modules and appliance wall

switches (note no dim/brighten facility). This

is radio based so you must have an TM12U

transceiver somewhere in your X10 system.

Requires 4 x AAA batteries (not included)

[RW8184] £29.99

DIGIMAX 210 X10 THERMOSTAT

The Digimax 210 is a wireless room thermostat

that communicates with the SC2800 base station.

Simply stick it on the wall, set it to the desired

temperature and it will communicate with the

base station, triggering an X10 on or off

command as the temperature rises or falls. Use it

with any heater plugged into an appliance

module, or with a bit of ingenuity (and probably

some help from a heating engineer) you could achieve X10 control of

your gas central heating system. Using the telephone integration

features of the SC2800 you could even call ahead and have your house

brought up to temperature ready for when you arrive. (note that the

Digimax 210 can only communicate via an SC2800 - it does not issue

X10 commands directly)

TECHNICAL DATA

Size : 80 x 80 x 25mm

Operating temperature range: 5°C to 35°C in 1° steps

Differential: <1°C at 4°C per hour

Ambient temp range: 0°C to 45° C

Power supply: 2 x AA batteries (not supplied)

Battery life: 2 years typical

RF frequency: 433.92 MHz

RF range: 30 metres (free air)

Approval: CE approved

[DM210] £34.99

Slimline stick-on wireless wall switch

A really thin (less than 5mm thick) light-weight

switch that can be attached to any wall in seconds,

giving you instant convenient control of up to three

X10 addresses. It sends commands to a transceiver

module by radio frequency to any consecutive

group of 3 unit codes within the same house circuit

setting and also has the dim up and dim down

facility. It is of particular use where a user may wish

to be able to control lighting or appliances in a

room from a static location and where the existing

wiring is insufficient to support a wall dimmer

switch or a wall appliance switch. It can also be of

great benefit when much more functionality is required in a home

and where the expense of a conventional wiring alternative would be

prohibitive. Like all other Home Control products it can be used to

activate sequences managed by a computer interface module. Because

it is battery operated, it may be used safely where conventional

wiring may be hazardous, for example in close proximity to water.

(note: unit itself not water resistant)

[SS13E] £29.99

Wireless (RF) transmitters (continued)

New X10 MicroModules

A great addition to the X10 range, these are very tiny modules that are

designed to be concealed behind existing wall sockets and switches.

AW12 MicroModule

A miniature appliance module that can be

concealed behind an existing wall socket to turn it

into an X10 controlled wall socket. It can also be

wired to an external switch (momentary or

latching) for direct control. A neutral wire is

required for operation. When used with a

momentary switch the relay will operate each time the switch is

pressed. When used with a latching switch the relay will operate on

both the closure and release. This means two-way switching is possible

if 2 changeover latching switches are connected in series.

Technical data: Supply voltage: 230V +10% -15% 50Hz, Supply current:

<20 mA capacitive. Max capacity: 2000W (incandescent lamp), 3A

(motors), 16A (resistive

[AW12] £49.99

AWM2 MicroModule

A miniature X10 transmitter for two addresses

with built in 16A appliance module. It can be used

to turn a conventional switch (momentary or

latching) into an X10 transmitter. If for example

the 1st switch is set to address A10 then the relay

will respond to an incoming command for A10. If

the switch is used it will switch the relay and also

send an X10 command to any other modules set

to A10. Switch 2 only transmits an ON/OFF

command for the configured address plus one – in our example A11.

The module dimensions are just 46 x 46 x 16mm.

[AWM2] £79.99

TMA4 MicroModule

A miniature X10 Transmitter for 4 addresses and

the commands ON and OFF. The TMA4 connects up

to four conventional (latching) switches by wire

leads and transmits up to four sequential X10

ON/OFF addresses. MicroModules use two-way X-

10 communication. Marmitek MicroModules are

designed to fit in the rear of European junction

boxes, behind any installed switch or outlet. The

module dimensions are just 46 x 46 x 16mm.

[TMA4] £79.99

TMD4 MicroModule

Essentially the same as the TMA4 although it also

sends DIM/BRIGHTEN X10 commands, and can be

used with momentary action switches only. The

dimensions are the same at just 46 x 46 x 16mm

[TMD4] £79.99

SW10 Shutter Switch

Switch for sun blinds, roman blinds, curtains

and other window coverings using a 230V

motor. Intelligent switch with memory for

window size and present position. Remote

control using the X10 protocol. With X10

control the blinds can be set in any position.

Manual control is also possible. The X10 Shutter

Switch can be built into a standard 50mm

Shuko back box. The switch can be controlled

remotely via the mains using X10 signals. This

means the Marmitek X-10 system can be built into the installation and

is totally ‘invisible’. The switch can also be controlled manually as a

momentary switch. The blinds can be set in any position manually.

When installing the switch, the size of the window is set. This

information is stored in memory and will be retained even in the event

of a power failure. This also applies to the actual position of the sun

blind. The blinds can be remotely controlled using the following X10

Commands:

• Fully open in response to the command ‘On’

• Fully closed in response to the command ‘Off’

• Any desired setting in response to the command ‘Dim’.

Phase and neutral have to be available before the module can be

installed.

[SW10] £49.99

Data sheets available on request or from www.keene.co.uk as pdfs

X10 receivers (things that act on receiving

an X10 command)

Visitors are welcome at our

showroom/warehouse. We have full

demonstration facilities – why not try before you

buy? Monday–Friday 9.00am–5.30pm, Saturday

9.00am–5.00pm

1 2 3 4 5 6 7 8

Komentáře k této Příručce

Žádné komentáře

RF-Max Digimax 210 Uživatelský manuál Strana 5

Komentáře k této Příručce

Související produkty a manuály pro Termostaty RF-Max Digimax 210